EV Charger Installation Sunshine Coast
Licensed EV charger installation from Noosa to Caloundra and across Brisbane's northside. We install any brand of charger, including one you already own, single or three phase, on its own compliant circuit with a real load assessment first, direct from the contractor doing the work.
SAA accredited for solar & battery, S6093214
Master Electricians member 23598 · QLD Lic# 92489
Nuvolt installs any EV charger, any brand, from Noosa to Caloundra and across Brisbane's northside, fitted by a licensed Queensland electrician direct from the contractor doing the work. Supplied by us or bought by you, Tesla Wall Connector, Zappi, Wallbox, Fronius Wattpilot, Ocular, Sungrow, Fox ESS or another brand, single or three phase, every charger goes on its own dedicated, RCD-protected circuit to AS/NZS 3000, with the switchboard and cabling work that goes with it. We start with a real load assessment so the charger will not trip your supply or overload an older board, and you get a fixed price before any work begins.
Get a Fixed-Price Quote for Your EV Charger
Tell us your vehicle, where you'd like the charger and whether you have single- or three-phase supply. We'll recommend the right unit, or fit a charger you already own, and give you a fixed price before any work begins.
- →Licensed & insured, direct from the contractor doing the work
- →Real load assessment so the charger won't overload your supply
- →Sunshine Coast, Brisbane Northside & greater QLD
Send your enquiry
Takes 30 seconds. We reply within 2 hours during business hours. If it is urgent, call 0425 547 520.
EV Charger Installation, Done Properly
An EV charger is a continuous, high-current load, not something to run off the nearest power point. Done properly, it's a dedicated circuit, the right protection, and a charger matched to your supply and your car. Nuvolt installs home and commercial EV chargers across the Sunshine Coast, Brisbane and surrounding Queensland regions, direct from the licensed contractor doing the work.
We start with a real load assessment so the charger won't trip your supply or overload an older switchboard, then install a smart, OCPP-compatible unit you can schedule, monitor and, if you have solar, charge from your own panels.
Already going solar?
If you're installing or upgrading solar & battery, adding an EV charger at the same time is the most cost-effective way to do it. One switchboard assessment, one visit, and charging that's aware of your solar generation.
Get a Quote →Charge at home, wired right
Sungrow and Fox ESS supplied and installed, or we fit any charger you already own: Tesla Wall Connector, Zappi, Wallbox, Fronius Wattpilot, Ocular and the rest, single or three phase. Configured by the licensed contractor who turns up. No call centres. No subbies.
Sungrow AC22E
The pick if you have, or plan to add, solar. Charges from your excess solar so daytime charging can cost next to nothing.
- Up to 22kW, single or three phase
- Solar-optimised charging modes
- Smart app control and scheduling
- Tethered Type 2 cable, ready to plug in
- 3-year manufacturer warranty
Fox ESS A Series
A tough, no-fuss unit for garage or driveway. App, RFID card or plug-and-charge, and it plays nicely with energy plans via OCPP.
- Up to 22kW, single or three phase
- IP55 rated for indoor or outdoor mounting
- Wi-Fi, RFID and app control
- OCPP compatible for smart energy plans
- 3-year manufacturer warranty
Not sure which charger suits your home? We check your switchboard and supply, then recommend the right unit. Already bought one? Send us the model and a photo of your board and we will price the install.
Servicing the Sunshine Coast, Brisbane and South East Queensland
Chargers we supply and install
Two brands, single or three phase, each with a fixed install price you can check online. Or bring your own charger and we install it.
From a Single Home Charger to Workplace Charging
Any brand, including your own charger
We install any EV charger: Tesla Wall Connector, Zappi, Wallbox, Fronius Wattpilot, Ocular, Sungrow, Fox ESS and others, single or three phase. Bring the unit you already own or bought elsewhere and we fit it on its own protected circuit, with the switchboard and cabling work that goes with it.
Home EV chargers
Wall-mounted home chargers on a dedicated, RCD-protected circuit, sited for a tidy cable run and easy daily use. Single-phase (typically up to 7kW) or three-phase (up to 22kW) where your supply allows.
Commercial & workplace charging
Multi-bay, staff and customer charging for businesses, with networked, OCPP-compatible chargers that support access control, usage reporting and billing where required.
Load assessment
Before quoting we check your main switch rating, existing load and available capacity so the charger won't overload your supply, and recommend dynamic load management where it's the smarter option to upgrading.
Switchboard considerations
EV chargers need their own correctly protected circuit. We check your switchboard for spare capacity, RCD/RCBO protection and compliant labelling, and flag any upgrade up-front rather than on install day.
Smart & OCPP chargers
Wi-Fi-connected, app-controlled chargers with scheduling, solar-aware charging and OCPP support so the unit isn't locked to a single vendor's back-end.
Solar-aware charging
Pair your charger with solar so you can top up from excess daytime generation instead of the grid. Works alongside a new or existing solar and battery system.
EV charger repairs and fault-finding
A charger that trips, will not start a session or has dropped off its app is usually a circuit, protection or settings problem. We fault-find chargers we did not install, fix the electrical side, and tell you straight if the unit itself has failed.
The Charger Is Only as Good as the Circuit Behind It
EV charging adds one of the largest sustained loads in a modern home. We check that your switchboard and supply can take it before we quote, so you don't end up with nuisance tripping or an unsafe install.
Not sure your board is up to it? A $199 electrical safety check covers exactly this. The $199 covers the full inspection and is credited back in full against any Nuvolt work you go ahead with, the charger install included.
What we check before quoting
- →Main switch rating and available spare capacity for a new high-current circuit
- →Single- vs three-phase supply and the charger speed it supports
- →RCD/RCBO protection and a dedicated, correctly labelled circuit
- →Whether dynamic load management avoids a costlier supply upgrade
- →Cable route and mounting position for a tidy, practical install
- →Network provider notification where higher-power chargers require it
From Quote to Plugged In
Site Consultation
Tell us your vehicle, where you'd like the charger and whether you have single- or three-phase supply. We confirm what's possible at your property.
Site & Load Assessment
We assess your switchboard, available capacity and cable run, then recommend the right charger and circuit, with load management if it avoids an unnecessary upgrade.
Compliant Install
A licensed electrician installs the charger on its own protected circuit to AS/NZS 3000, mounts it neatly and commissions the unit and its app.
Test & Handover
We test everything, walk you through charging and scheduling, and provide the appropriate Queensland electrical certificate on completion.
EV Charging Questions
Straight answers on circuits, switchboards, charger speeds and solar charging, from the contractor doing the work.
Do you install EV chargers of any brand?
Yes. We supply and install Sungrow and Fox ESS chargers, and we install any other brand you choose: Tesla Wall Connector, Zappi, Wallbox, Fronius Wattpilot, Ocular and the rest, on single or three phase. Every one goes on its own dedicated, RCD-protected circuit with the switchboard and cabling work it needs.
Can you install a charger I already own or bought online?
Yes. Bring the unit you bought with the car, online or from another supplier and we fit it. The electrical work is the same job whoever supplied the charger: load assessment, dedicated circuit, protection, mounting, commissioning and the certificate at the end. Send us the model and photos of your switchboard and we will quote it as a fixed price.
Do you install Tesla Wall Connectors?
Yes, on single or three phase, and it is one of the chargers we fit most often. The Wall Connector needs its own correctly protected circuit like any other hard-wired charger, and we handle the switchboard side, the cable run and the commissioning through the app.
Do I need a dedicated circuit for an EV charger?
Yes. An EV charger must run on its own dedicated, RCD-protected circuit from the switchboard, sized for the charger's continuous load. We never share it with other appliances.
Can my switchboard handle an EV charger?
Often yes, but it depends on your main switch rating, current load and spare capacity. We assess this before quoting. Where capacity is tight, dynamic load management can let you charge safely without a full supply upgrade.
Should I get a single-phase or three-phase charger?
Single-phase chargers (typically up to 7kW) suit most homes and add plenty of range overnight. Three-phase chargers (up to 22kW) charge faster but need three-phase supply at the property. We'll confirm which you have and what your car can actually accept.
What is load management or dynamic load balancing?
It lets the charger automatically reduce its draw when the rest of the home is using power, so you stay within your supply limit. It's often a cheaper, smarter alternative to upgrading your main supply.
Can I charge my EV from my solar?
Yes. A solar-aware smart charger can prioritise excess solar generation, so you charge from your own panels during the day instead of the grid. It works with a new or existing solar and battery system.
Do you install EV chargers for businesses?
Yes. We install workplace and commercial charging with networked, OCPP-compatible units that support access control and usage reporting, scaled to the number of bays you need.
Will my energy provider need to be notified?
Higher-power and three-phase chargers can require notification to your network provider. Where that applies, we handle the paperwork as part of the job.
How long does an EV charger installation take?
A typical home install is completed in a single visit. Time varies with cable-run length, switchboard work and whether a supply upgrade is needed. All confirmed in your fixed-price quote first.
Do you install EV chargers in Noosa and the northern end of the coast?
Yes. Noosa, Noosaville, Tewantin, Peregian and Coolum are on our regular runs from the Nambour workshop, along with Maroochydore, Buderim and Caloundra to the south. Brisbane's northside is covered as booked work.
Do you repair EV chargers?
Yes. A charger that trips the board, will not start a session or has lost its app connection is usually a problem with the circuit, the protection or the settings rather than the unit, and we fault-find chargers we did not install. If the charger itself has failed we tell you so, and we can fit the replacement on the existing circuit.
Related services
Ready to Charge at Home?
See your fixed EV charger install price online in under a minute, or book a $99 site inspection with a same day quote for anything non-standard.
Where we do this
Home and commercial EV chargers go in across the Coast and greater Brisbane. These are our most common install areas.